Sanding discs
-
- Junior Member
- Posts: 19
- Joined: June 15th, 2014, 10:34 pm
- Enter the middle number please (3): 3
- Location: Tasmania, Australia
- Contact:
Sanding discs
Hi guys
Done my first fews HLRs this week...excellent results thanks to excellent DK equipment.
How many times can you use the same disc for? Guessing the coarser ones for longer than the finer ones? Or is it best to just use new sets for each job?
Thanks
Done my first fews HLRs this week...excellent results thanks to excellent DK equipment.
How many times can you use the same disc for? Guessing the coarser ones for longer than the finer ones? Or is it best to just use new sets for each job?
Thanks
-
- Senior Member
- Posts: 742
- Joined: June 16th, 2009, 11:28 pm
- Enter the middle number please (3): 3
- Location: NC
- Contact:
Re: Sanding discs
Good morning. I normally use the disc once per set of headlights, except for the 3000 foam polishing pad. I use the used ones sometimes on headlights that might require additional pads.
-
- Junior Member
- Posts: 19
- Joined: June 15th, 2014, 10:34 pm
- Enter the middle number please (3): 3
- Location: Tasmania, Australia
- Contact:
Re: Sanding discs
Yes I thought that was about right. Really when you think of trying to save a quid its probably not worth it as you could end up wasting more TIME trying to use a worn disc.
Results are perfect with new ones so I will stick to that.
Thanks
Results are perfect with new ones so I will stick to that.
Thanks
-
- Senior Member
- Posts: 742
- Joined: June 16th, 2009, 11:28 pm
- Enter the middle number please (3): 3
- Location: NC
- Contact:
Re: Sanding discs
When you finish a set, normally the 320,500, 800, have dust build up or bumps on them. They can create a problem or cause swirls when used on another set of HLs. Those dust bumps can burn into the HL if not cautious, requiring additional sanding to remove them.
-
- Senior Member
- Posts: 1058
- Joined: April 12th, 2008, 8:47 pm
- Enter the middle number please (3): 5
- Location: U.S.
- Contact:
Re: Sanding discs
Do every job to your best ability. Reusing old pads is not the way to make happy customers. The cost of the pad is negligible to the overall cost.
The swirl marks mentioned above are called pig tails and they are hard to remove and very time consuming.
Just my opinion...
The swirl marks mentioned above are called pig tails and they are hard to remove and very time consuming.
Just my opinion...
- Brent Deines
- Moderator
- Posts: 2449
- Joined: September 24th, 2003, 7:54 am
- Enter the middle number please (3): 5
- Location: Eugene, OR
- Contact:
Re: Sanding discs
I learned this years ago when sanding wood and the same applies here. Using a worn out disc will cost you time and money every time.
Brent Deines
Delta Kits, Inc.
Delta Kits, Inc.
-
- Member
- Posts: 232
- Joined: May 20th, 2012, 1:05 pm
- Enter the middle number please (3): 3
- Location: South Elgin, IL
- Contact:
Re: Sanding discs
Old thread but........... I get about seven cars out a of a 3000 pad. They are meant for more than one car. I picked that up from a paiint guy who has a bunch of used foam pads laying around. He reuses them unil they loose shape. They work for me.
I also keep a box for used discs (500-1500). We all have cars that only need one HL done. This is good for the next car that needs one HL done.
I also keep a box for used discs (500-1500). We all have cars that only need one HL done. This is good for the next car that needs one HL done.
Paul Weinstein
- Brent Deines
- Moderator
- Posts: 2449
- Joined: September 24th, 2003, 7:54 am
- Enter the middle number please (3): 5
- Location: Eugene, OR
- Contact:
Re: Sanding discs
To each his own if that works for you but I find just the opposite to be true for me. If a headlight lens is not clearing up as well as I would like and I'm confident I have done all the previous sanding steps properly I'll switch to a new 3000 polishing pad. Every single time there is improvement. I also don't save used sanding discs as I find the extra time it takes costs me more in labor cost than a new disc and if a disc is not cutting as well as I think it should I'll put on a new one.
I also know a number of body shop owners and I don't know any of them who re-use sanding discs. If anything, they change them sooner than I do.
Want to buy my lightly used discs?
I also know a number of body shop owners and I don't know any of them who re-use sanding discs. If anything, they change them sooner than I do.
Want to buy my lightly used discs?
Brent Deines
Delta Kits, Inc.
Delta Kits, Inc.
-
- Senior Member
- Posts: 1058
- Joined: April 12th, 2008, 8:47 pm
- Enter the middle number please (3): 5
- Location: U.S.
- Contact:
Re: Sanding discs
I agree 100% with all of the above!Brent Deines wrote:To each his own if that works for you but I find just the opposite to be true for me. If a headlight lens is not clearing up as well as I would like and I'm confident I have done all the previous sanding steps properly I'll switch to a new 3000 polishing pad. Every single time there is improvement. I also don't save used sanding discs as I find the extra time it takes costs me more in labor cost than a new disc and if a disc is not cutting as well as I think it should I'll put on a new one.
I also know a number of body shop owners and I don't know any of them who re-use sanding discs. If anything, they change them sooner than I do.
Want to buy my lightly used discs?
The cost of the discs are the smaller part of the overall job for me.
-
- Member
- Posts: 232
- Joined: May 20th, 2012, 1:05 pm
- Enter the middle number please (3): 3
- Location: South Elgin, IL
- Contact:
Re: Sanding discs
Guys, Im talking about the 3000 discs at $1.00 a piece. If your using them for just one car, your throwing money out the window. Those pads are intended for more than just one use.
As a matter of fact, Im going to go as far as this: I dont like when I have to use a new one. It doesnt leave the lens as clear and sort of gray looking. One thats been used a couple of times works much better. Heres an example of a HL that I did that I know had a well used 3000 pad. I know it because while I was in the field, I thought I had more with me but had to use a well worn one and was surprised how lucky I was that they came out looking good.
As a matter of fact, Im going to go as far as this: I dont like when I have to use a new one. It doesnt leave the lens as clear and sort of gray looking. One thats been used a couple of times works much better. Heres an example of a HL that I did that I know had a well used 3000 pad. I know it because while I was in the field, I thought I had more with me but had to use a well worn one and was surprised how lucky I was that they came out looking good.
Paul Weinstein
Who is online
Users browsing this forum: No registered users and 1 guest