really really bad work

[tooldini]

I usually pass on them since most of my work is insurance referrals. I don't want to be held responsible for someone elses nasty looking repair. I see many around here that look untouched except they have a pitfill in them LOL

Jeff

[harrellbenjamin]

On my invoice I always note location by diagram of any old damage repairs.I explain this was already there.It helps to cut out any "misunderstandings in the future in event of a crack etc.

As far as sharing info with "the chosen few" about old repair techniques just consider the comments for what they are.I for one would appreciate any input you would have about success in old repair improvement.Some techs on here like to live life vicariously through this site and make windshield repair to be something its not.This aint rocket science......................

[harrellbenjamin]

Originally Posted by glassdoctor

Don't even know where to start so I'll leave it alone. But it's just begging to be picked apart. killing me, lol....

jayjacque:
I do a lot of old repair work. Perhaps public posting isn't the best place to talk about how to do them. If the forum rules allow... you can email me, or call me. It would be easier than arguing with the boys here.

Often, the worse the original repair job, the easier it is to re-do it. The kind you describe sound like perfect candidates. But as stated, I won't go into details. Maybe some others will post some tips.

Dont let any of those self absorbed people intimidate you.I appreciate your knowledge.This is windshield repair!!!!!!!!!! You get certified after a 1 day class..............LOL I would bet many who preach have been making the same mistakes over and over for years.I feel real sorry for people that have to make their selfs feel important due to things that have made them feel small in the past.Its a pity.

Now ,what were those tips for making old repairs look better? I guess we have a way now to see who would fit your discripion by the comments you will receive.lets have a go at it please!!!!!!!!!!!!!

[screenman]

I do rerepairs sometimes, in fact sometimes my own that have failed for some reason. Normaly failing to dry out properly, when working in the conditions we sometimes have to it is hard to see. This is my excuse, anyway I tend to burn out the old damage as much as possible to open it up, we have been throught this before in older posts. I was then told I should not have given this information to a newbie.

Its funny that old repairs that were obviuosly injected wet and then capped with pit fill will be dry when you redo. Where does the moisture go to.
Make sure when you sell the job you give the customer as much information as possible.

Everyone have a good weekend.

[glassdoctor]

pretty funny screenman... it's magic water. It will fight to the death to stay inside when you want it out, then after you lose, it gives up pulls a Houdini and magically disappears.

The H2O evaporates right through the resin I believe. Obviously it takes a while...

I hesitate to give out any "how to" advice (on some subjects) on the forum anymore. I used to do a lot here. But I have had a good dealer account and a couple other vendors in my area pick up Delta equipment and it has cost me some work. I'm sure they can learn a lot on this forum if they choose to be here... but I would prefer to not add to it. I know they have been here, and in the past I have unknowingly helped one of them.

I know this thinking has been criticized here in the past, but to each his own I guess. I doubt you would take that position if you have been burned.

It's good to see some of the old familiar names on here.. be glad to discuss with most of you guys.

Besides, it would take some really lengthy posts to cover any ground on this topic. And, it's not for everyone either.

I think screenman is right... it's probably been discussed in the past.

What you need:

torch... drill... pick...tapper

and a lot of nerve

[screenman]

Love the Houdini bit, I would add a hammer to the tool list.

[glassdoctor]

Like someone just said... it's not rocket science... think of the break. Be the break, lol.

Oh.. and most do not come out perfect, and sometimes you can only get a partial improvement. But some do turn out very very well. It just depends on how the break reacts... they can fool you.

I have had some I thought would be easy, but kicked my butt. And others I thought impossible, and came out pretty good.

some basic tips:
bullseye... torch it
star... rout out the pit and "tap it" into a combo
combo... cross your fingers and torch/tap it

Keep in mind things can go south in a hurry when reworking repairs. I suggest you not experiment on jobs that are important.

[glassdoctor]

hammer.. yeah. sometimes I really want to grab a hammer and show the w/s who is the boss!!! LOL!!!

[Chips-B-Gone]

Originally Posted by Brent Deines

I believe a repair is either done right, or not done right, so "good enough" is not a term in my vocabulary.

Amen Brother.. I spent over 2 hours on a combo that should have taken 20 minutes but due to changing temperature and trapped air I would not quit until it was done. Not to brag on myself or anything but when a dealer, or any customer, sees that kind of pride in my work I WILL get another call from them!

[glassdoctor]

2 hours man?????

You deserve some kind of cub scouts award or something. lol