What tape do you use to mask?

Discuss all aspects of headlight restoration, including marketing, technical, and business advice.
Post Reply
Old Blue 66
Member
Posts: 232
Joined: May 20th, 2012, 1:05 pm
Enter the middle number please (3): 3
Location: South Elgin, IL
Contact:

What tape do you use to mask?

Post by Old Blue 66 »

I use the 3M 1 1/2 blue painters tape. I double up on it while masking set of lenes. Its priced almost every where at about $33 for a 6 pack. Very expensive. Anything else someone has been successful using??

http://www.amazon.com/3M-ScotchBlue-Pai ... B00125PS5Y
Paul Weinstein
candyman
Senior Member
Posts: 742
Joined: June 16th, 2009, 11:28 pm
Enter the middle number please (3): 3
Location: NC
Contact:

Re: What tape do you use to mask?

Post by candyman »

I use the same brand. I've tried other brands and had poor results. Problems: Too much adhesive pulls paint off bumper or molded plastic fender. Tearing quickly if you should hit it with the orbital. Not holding and releasing prior to finshing the job. I always double tape along the bottom of the light or tight areas. Old saying. Penny saved or pound for cure.
Image
glassdoctor
Senior Member
Posts: 733
Joined: November 13th, 2003, 9:24 am

Re: What tape do you use to mask?

Post by glassdoctor »

I think you are doing a bit of overkill with 2x layers of tape. Unless you have a really difficult corner, etc (just double up on that one spot).... you should be fine with 1 layer, like 95% of the time. That will cut your tape expense by half.

Anyway, tape is stupid expensive. I like the Scotch/3M for sure. I've also used a slightly cheaper brand from walmart/menards, etc. (duck?) I use 1" blue tape so it's more like $3/roll. If I need more coverage for some reason, I can lay down an extra strip. But I'm not wasting $ by using $5-6 tape where it's not necessary.
candyman
Senior Member
Posts: 742
Joined: June 16th, 2009, 11:28 pm
Enter the middle number please (3): 3
Location: NC
Contact:

Re: What tape do you use to mask?

Post by candyman »

I use to pay about 3.99 for 1 1/2 inch. Now its about $6. I will catch a sale and get about 5 rolls of 2 inch for about $29.99.
Image
User avatar
ctmandu1
Junior Member
Posts: 25
Joined: July 6th, 2012, 3:43 pm
Enter the middle number please (3): 3

Re: What tape do you use to mask?

Post by ctmandu1 »

if you double up just use the blue on the bottom layer and use cheap masking tape for the second layer, its allot cheaper that way and the blue last allot longer... just my 2cents worth
Image
Old Blue 66
Member
Posts: 232
Joined: May 20th, 2012, 1:05 pm
Enter the middle number please (3): 3
Location: South Elgin, IL
Contact:

Re: What tape do you use to mask?

Post by Old Blue 66 »

Ill give that a shot. I like to double up becuase its still a LOT cheaper than fixing a bumper or getting a customer angry.
Paul Weinstein
User avatar
pommy
Member
Posts: 258
Joined: August 24th, 2011, 11:20 pm
Enter the middle number please (3): 3

Re: What tape do you use to mask?

Post by pommy »

I've "caught" a few awkward bars before.

If it's a car yard - I polish them with the GT compound, that normally polishes them out.

If not and there's a slight sign of the scuff still...when you apply the Infinity - accurately, wipe some over the scuff - it will vanish ;)

Skeptics welcome ;)

Cheers,

Pommy
If the job doesn't mean more than the pay, it will never pay more.
Post Reply

Who is online

Users browsing this forum: No registered users and 45 guests